Skip to main content

Time Domain Reflectometer (TDR) for Network Professional

As a network engineer/administrator, you would encounter the cabling problem of patch panel to host, patch panel to switch, switch to switch.

In these scenarios, you can determine whether switch or physical layer (Layer 1 ) issue or not before contacting to cabling contractor.

To do so, you can use below commands.

show interface
show interface counters
show interface counters errors

Moreover, you still can find the cabling issue with another testing method. That is Time Domain Reflectometer.

To test this in cisco switch, use below commands.

test cable tdr interface port number

show cable-diagnostics tdr interface port number

You will know how to use it from below sample pictures.





If you are testing FastEthernet, Pair A and Pair B result must be Normal.
If you are testing GigabitEthernet , all Pair must be Normal.

Other than that result, you need to find out where is the distance that cable becoming fault.

The approximate cable fault distance is shown in result.

Yes, I believe you know the basic of TDR now.

This feature is include not only on Cisco Switch but also you can find in other brand switch like juniper, hp and dell.

If you want to know more about this in details, please go and read from below link.
https://supportforums.cisco.com/document/74231/how-use-time-domain-reflectometer-tdr 

Have a good time.
(Be knowledgeable, pass it on then)

Comments


  1. There are miscellaneous expenditures in the production of the Reflectometry.
    The producers, the studio executives and the Reflectometry can monitor the Weekly Cost Report to get familiar with how much is been spent in comparison to the approved budget.
    More in fo: Reflectometry

    ReplyDelete
  2. Hi...You were told to run away. Soak the place, and light the flame pay the price for your betrayal. Your betrayal, your betrayal!Read more-Reflectometry

    ReplyDelete
  3. Hi admin,
    I really like it, I have also a blog which is related with you, which is about Reflectometry.
    Also, the basic concept of translating creative ideas into a budgeting process is new to most people, especially those educated in film schools, so that concept should be presented first.
    You’ll need to buy my book at this link Walk The Talk to get that inside advantage.
    Reflectometry

    Thanks,

    jahaingir alam

    ReplyDelete

Post a Comment

Popular posts from this blog

Fortigate guide for Begineer - 6

I would like to explaine how to troubleshoot the Fortigate Unit configured by Transparent Mode in step by step this time. Let's assume, you have one Fortigate Unit that configured as Transparent Mode. But devices from Internal/Private Network unable to access Internet/Public Network through your Fortigate Unit. OK. Let's troubleshoot with following steps, 1) Check the physical network connections between the network and the FortiGate unit, and between the FortiGate unit and the Internet. 2) Check the router and ISP-supplied equipment to make sure it is operating correctly. 3) Verify that you can connect to the internal interface by connecting to the management IP address of the FortiGate unit from the Internal network. From the internal network, attempt to ping the management IP address. If you cannot connect to the internal interface, verify the IP configuration of the PC and make sure the cables are connected and all switches and other devices on the network are powered on a

Solving the "A general system error occured:Invalid fault" error in vSphere 4

Below error was come out when you try to migrate VM to other host for some reason. Below error was come out when you try to edit VM setting. Below error was come out when you power on the VM. How to solve those error? Here is how I resolve the error! Login to the Host that errored VM exist by using Terminal or Direct Console. Enter below command and press enter. services.sh restart Wait until all VMware Services are restarted. After that try to Power On/Edit Settings or Migrate the errored VM and you will see all you can do without any error pop-up. This kind of errors can occur if you shutdown/restart VM unproperly or shutdown/restart the Host unproperly that VM exist. You can check log file deeply if you willing to know precisely on this. May you all be happy. (Be knowledgeable, pass it on then)

Link Aggregating with Synology NAS and Cisco Switch

I’d like to share how to setup Link Aggregating between Synology NAS and Cisco Switch. I’ve got one Synology NAS with 4 Network Ports and I’m going to use 2 of them. Both Network Port to be as one Logical Link, Fault Tolerance and Load Balancing. To do that, I need to configure Link Aggregating on Synology NAS and EtherChannel with LACP on Cisco Switch. Below is brief steps to do to meet with my requirements. - Get connected Synology NAS and Cisco Switch as shown in picture. - Bonding two Network Ports of Synology NAS and assign IP Address - Configure EtherChannel with LACP in Cisco Switch and add two physical ports as Member. OK. Let’s begin from Synology NAS. - Login to the Synology and go to Control Panel>Network>Create>Create Bond - Select IEEE 802.3ad to get Fault Tolerance and Load Balancing Featureyou’re your switch not support 802.3ad you can only select Fault Tolerance only feature). After that click “Next”. - Choose the network port f