Skip to main content

OpenSSL X509_cmp_time DoS

By

After receiving the certificate (either from client to server or server to client) OpenSSL calls X509_cmp_time to perform various checks on the certificate including comparison of notBefore and notAfter validity times against the current time. The function allocates buffer to store bytes in VisibleString. The malformed VisibleString can lead to a read read-access violation, which leads to termination of application

Using crafted certificate with malformed UTCTime or GeneralizedTime field Remote attacker can exploit this vulnerability causing denial of service.

The vulnerability is referred by CVE as CVE-2015-1789.

If your security devices haven’t patch for this vulnerability, kindly look for update and patch it.

If you are using Security Devices from Dell SonicWall, Dell SonicWALL has released an IPS signature to detect and block exploitation attempts targeting this vulnerability. The signature is listed below:

  • 11109 OpenSSL X509 DoS
  • 11110 OpenSSL X509 DoS 1

Have a good time
(Be knowledgeable, pass it on then)
Labels:

Comments

Post a Comment

Popular posts from this blog

Fortigate guide for Begineer - 6

By
I would like to explaine how to troubleshoot the Fortigate Unit configured by Transparent Mode in step by step this time. Let's assume, you have one Fortigate Unit that configured as Transparent Mode. But devices from Internal/Private Network unable to access Internet/Public Network through your Fortigate Unit. OK. Let's troubleshoot with following steps, 1) Check the physical network connections between the network and the FortiGate unit, and between the FortiGate unit and the Internet. 2) Check the router and ISP-supplied equipment to make sure it is operating correctly. 3) Verify that you can connect to the internal interface by connecting to the management IP address of the FortiGate unit from the Internal network. From the internal network, attempt to ping the management IP address. If you cannot connect to the internal interface, verify the IP configuration of the PC and make sure the cables are connected and all switches and other devices on the network are powered on a...
Post a Comment
Read more

Why do we need network virtualization?

By
We need to think about Server Virtualization first if we want to talk about Network Virtualization. In the era of cloud computing, servers are virtualized and used in Data Centers. We are facing a lot of problem when we virtualized our Servers, 1) Routing and Switching Problem Routing become the issue when we create Virtual Switch and VLANs according to production requirement. Network Team might need some time to change on their end to meet with Server Virtualization Team changes on their end. ၂) Firewall Services Physical Firewall are difficult to manage due to the large number of rules needed to satisfy business requirements. New applications, new projects, and new networks all come with potential security requirements, which impact centralized firewall management. ၃) Load Balancing Let's say your company deploys a new physical load balancer for each tenant, resulting in increased capital expenditures. Once a tenant reaches their maximum capacity, it ca...
144 comments
Read more

Link Aggregating with Synology NAS and Cisco Switch

By
I’d like to share how to setup Link Aggregating between Synology NAS and Cisco Switch. I’ve got one Synology NAS with 4 Network Ports and I’m going to use 2 of them. Both Network Port to be as one Logical Link, Fault Tolerance and Load Balancing. To do that, I need to configure Link Aggregating on Synology NAS and EtherChannel with LACP on Cisco Switch. Below is brief steps to do to meet with my requirements. - Get connected Synology NAS and Cisco Switch as shown in picture. - Bonding two Network Ports of Synology NAS and assign IP Address - Configure EtherChannel with LACP in Cisco Switch and add two physical ports as Member. OK. Let’s begin from Synology NAS. - Login to the Synology and go to Control Panel>Network>Create>Create Bond - Select IEEE 802.3ad to get Fault Tolerance and Load Balancing Featureyou’re your switch not support 802.3ad you can only select Fault Tolerance only feature). After that click “Next”. - Choose the network port f...
35 comments
Read more