Skip to main content

Fortigate guide for Begineer - 9

By

In general, Computer from Finicial Department of Company Network have to be IP Reserved to working properly with their Finicial Software.

For example, the Computer that installed Blommberg Software need to get fixed IP address to connect Bloomberg server for Transaction. If that Computer changed IP address frequently, Bloomberg unable to connect to it's server.

So, you have to reserved the IP address of that Computer within the DHCP Range that provide from Fortigate Unit in Company Network.

Here is the steps to Reserved IP Address in Fortigate for exact Computer.

1) Log in to Fortigate Unit and Go to System > Network > DHCP Server and Edit the DHCP server.
2) Select IP Reservation and select Create New and add a MAC IP address pair. (The IP address must be within the range defined by the DHCP server.)

The above steps are for the Computer that hasn't connect to Fortigate Unit yet.

If the PC is already connected and has acquired an IP address from the DHCP server, you can
set get its MAC address and IP address by selecting Add from DHCP Client List. When the
list appears, select the PC from the list and select Add To Reserved.

Reservation the IP Address is done!

May you all be happy.
(Be knowledgeable, pass it on then)
Labels:

Comments

Post a Comment

Popular posts from this blog

Fortigate guide for Begineer - 6

By
I would like to explaine how to troubleshoot the Fortigate Unit configured by Transparent Mode in step by step this time. Let's assume, you have one Fortigate Unit that configured as Transparent Mode. But devices from Internal/Private Network unable to access Internet/Public Network through your Fortigate Unit. OK. Let's troubleshoot with following steps, 1) Check the physical network connections between the network and the FortiGate unit, and between the FortiGate unit and the Internet. 2) Check the router and ISP-supplied equipment to make sure it is operating correctly. 3) Verify that you can connect to the internal interface by connecting to the management IP address of the FortiGate unit from the Internal network. From the internal network, attempt to ping the management IP address. If you cannot connect to the internal interface, verify the IP configuration of the PC and make sure the cables are connected and all switches and other devices on the network are powered on a...
Post a Comment
Read more

Why do we need network virtualization?

By
We need to think about Server Virtualization first if we want to talk about Network Virtualization. In the era of cloud computing, servers are virtualized and used in Data Centers. We are facing a lot of problem when we virtualized our Servers, 1) Routing and Switching Problem Routing become the issue when we create Virtual Switch and VLANs according to production requirement. Network Team might need some time to change on their end to meet with Server Virtualization Team changes on their end. ၂) Firewall Services Physical Firewall are difficult to manage due to the large number of rules needed to satisfy business requirements. New applications, new projects, and new networks all come with potential security requirements, which impact centralized firewall management. ၃) Load Balancing Let's say your company deploys a new physical load balancer for each tenant, resulting in increased capital expenditures. Once a tenant reaches their maximum capacity, it ca...
144 comments
Read more

Link Aggregating with Synology NAS and Cisco Switch

By
I’d like to share how to setup Link Aggregating between Synology NAS and Cisco Switch. I’ve got one Synology NAS with 4 Network Ports and I’m going to use 2 of them. Both Network Port to be as one Logical Link, Fault Tolerance and Load Balancing. To do that, I need to configure Link Aggregating on Synology NAS and EtherChannel with LACP on Cisco Switch. Below is brief steps to do to meet with my requirements. - Get connected Synology NAS and Cisco Switch as shown in picture. - Bonding two Network Ports of Synology NAS and assign IP Address - Configure EtherChannel with LACP in Cisco Switch and add two physical ports as Member. OK. Let’s begin from Synology NAS. - Login to the Synology and go to Control Panel>Network>Create>Create Bond - Select IEEE 802.3ad to get Fault Tolerance and Load Balancing Featureyou’re your switch not support 802.3ad you can only select Fault Tolerance only feature). After that click “Next”. - Choose the network port f...
35 comments
Read more